How to start a husqvarna riding lawn mower?

How to start a husqvarna riding lawn mower?

Pre-Start Checklist

Before you start your husqvarna riding lawn mower, it’s important to do a few pre-start preparations. Doing this will not only help ensure your safety, but can also help prevent damage to the machine from an improper start-up.

To get you ready to go, here’s a pre-start checklist that you can follow to make sure everything is in order before you start the engine:

  1. Check the oil level.
  2. Check the fuel level.
  3. Check the air filter.
  4. Check the spark plug.
  5. Check the battery.
  6. Check the safety switch.

Read the owner’s manual

Before starting your Husqvarna riding lawn mower, it is important to read the owner’s manual thoroughly. The manual contains all the information you need to properly use and maintain your new mower. It is critical that you carefully read and understand this information before operating the machine.

In particular, pay attention to any special conditions for safe operation, such as wearing protective clothing and complying with local laws and regulations. Additionally, familiarize yourself with basic parts of the machine and learn how they work together. Furthermore, be sure to check all safety devices on the machine and make sure they are in good working condition before each use.

Following these steps can help ensure everyday safe operation of your Husqvarna riding lawn mower.

Check the fuel level

Before starting an engine, it is important to make sure the fuel tank is full or at least has enough gas for at least the duration of the trip you intend to take. The easiest way to determine what type of fuel is needed is to consult your owner’s manual. For example, most two-stroke engines require pre-mixed gas and oil while four-strokes generally use regular octane unleaded gasoline.

Checking your fuel level before starting a task or journey will ensure optimal performance of your engine and improved reliability. Depending on the model, some engines may include a monitor that will notify you when the fuel level is low; in this case, topping up promptly before any further use is essential to avoid any unnecessary complications or damage to your machinery.

Check the oil level

Before attempting to start your riding lawn mower, it is important to check the oil level. This can be done conveniently with a dipstick located near the engine. Your lawn mower manual will have detailed instructions on how to perform this task.

  • Generally, you should remove the dipstick and wipe it clean with a cloth or towel, then fully insert it again.
  • After you remove the dipstick for a second time, examine its tip for an accurate reading of the oil level and its condition.
  • If the oil is below the indicated “low” mark, top off with new oil as necessary; however, avoid adding too much oil, as this could cause engine damage.
  • In addition, ensure that you use only engine oils recommended in your manufacturer’s instructions and not any other type of fluid or lubricant.

Check all safety features

Before attempting to start a Husqvarna riding lawn mower, it is important to check all safety features. Make sure the parking brake is securely engaged and that the blades have stopped completely before making any attempts at engine starting. Check the ignition switch for proper operation before proceeding. Do not turn the key unless you are certain all safety features are in order and operational.

It is also important to look for any pieces of debris or foreign objects that may be lodged inside or under any moving parts of the lawn mower, such as the blade, deck or motor. Carefully remove any hazardous items prior to operating your lawn mower.

Additionally, make sure that you have fuel stored properly in approved containers designed specifically for gasoline storage and transport. Never use any other type of container when storing or handling fuel as this can be an extreme health hazard if mishandled or exposed to heat or direct sunlight. Examine power cords and batteries for any visible damage prior to operation as well; replace damaged components immediately if found before trying to start your lawn mower up again.

Starting the Mower

Starting a Husqvarna riding lawn mower is easy and straightforward. With the proper preparation, you can get your Husqvarna up and running in no time. This guide will provide all the information you need to know about starting the mower, from the fuel you should use to the safety protocols you should follow. Read on to find out how to get your Husqvarna ready for use.

Insert the key into the ignition

Before attempting to start your mower, ensure that the area is clear and that you are wearing protective gear such as gloves, a face-mask, safety glasses and hearing protection. Also, double-check to make sure the mower blades have stopped rotating before you start.

Once you have taken the necessary precautions to protect yourself and your surroundings, locate the ignition slot at the back of the engine. Insert the key into this slot and then turn it slowly clockwise until it locks into place. This will arm your mower’s ignition system so that when you push down on the start button or pull on the cord (depending on your type of mower), fuel will be dispatched to power up your engine.

Take special care not to over-torque or force the key into place as this may damage your ignition system and potentially render your mower inoperable.

Set the choke

Before attempting to start the mower, it is important to ensure that all proper steps are taken such as making sure the battery is charged and the fuel tank is filled with fresh gasoline.

The first step needed to start the Husqvarna riding lawn mower is to set the choke. The choke makes it easier for the lawn mower to start because it helps keep more air-fuel mixture in the combustion chamber than usual. To set the choke, slide open the control lever located near the bottom of your ride mower’s engine. Slide open until you hear a click, then continue sliding until it reaches its full open position. This should not be done if your engine has been running recently or if starting in warm weather conditions.

Turn the key to start the engine

Starting the engine is the first step to begin lawn mowing with your Husqvarna riding mower. To start the engine, you will need to follow a few basic steps.

Before starting, locate the safety switches near the seat and ensure they’re activated. You should also make sure that the choke is set correctly depending on how fast or slow you want your engine to run. Take note that if it is too cold outside, it’s particularly important to check these settings. Next, step on the clutch pedal, then push forward and hold it down while you press the brakes (or park brake) with your foot.

Now turn on your ignition key by rotating it to clockwise position – this will bring your engine from power “off” (stealth mode) to power “on” status. Once these safety precautions are in place, slowly turn your key to start position and release as soon as you hear or feel a jolt as this indicates that your engine has started.

You can now slowly ease off of brake pedals and clutch pedal by releasing pressure evenly using both feet together until they touch the floorboard – allowing for full freedom of operation on a neutral gear lever position. While maintaining light pressure on both pedals to prevent a sudden shift into gear mode, adjust throttle setting depending on speed desired while engaging blades via switch located just beneath seat. Now press pedal again – without switching ignition off – and then proceed with mowing operations!

Adjust the choke as needed

When operating your Husqvarna riding lawn mower, it is important to make sure the choke is adjusted properly. The choke helps control the flow of fuel to the engine, allowing it to warm up and allowing you to start the engine. If you have a model with a manual choke, you will need to move the lever as needed before starting it. For those with a spring-loaded or semi-automatic choke, you don’t need to do anything except turn on the ignition switch and attempt to start the engine.

When turning on your mower in cold or wet weather, check and ensure that all of your controls are in their proper positions, including both brake levers for safety. Then adjust your choke based on temperature: in cold weather move the lever all the way up, while in warmer weather only partially open it by moving it halfway up and half down. With automatic or semi-automatic chokes this will be done automatically in most cases but still needs adjusting on cold days.

Once you are ready, securely grab onto both steering handles so that they won’t move while operating and turn on the ignition key until you hear a click (you may have to jiggle around with the key). This means that everything has been set correctly and now you can pull on either rope handle twice slowly until hearing your engine come alive with a roaring sound. Make sure that both brake levers remain engaged until after your engine has started up – then they can be released before driving away.

Operating the Mower

Operating a Husqvarna Riding Lawn Mower can be easy if you follow a few simple steps. Before starting the mower, make sure you check the oil and fuel levels, and ensure that the safety systems are engaged. Additionally, you should familiarise yourself with the operator’s manual, as each mower may have slight differences in its operation.

Once you’re ready to go, you’ll need to select the appropriate gear, start the engine, and drive. In the following sections, we’ll discuss in more detail how to properly and safely operate your Husqvarna Riding Lawn Mower.

Put the mower in gear

In order to begin operating the mower, you must first put it in gear. Place your feet securely on the footrest and note the placement of your feet. Make sure that the PowerTake-Off (PTO) switch is in its off position (down or disengaged) and that the Throttle Control lever is in its idle position.

Move the gearshift lever located on the side of the machine up into whatever forward gear you want to use – usually either 1st or 2nd – then move it backward into its reverse position. To do this, pull up on the shifter until you hear a click and feel it engage into place. Check to make sure that all switches are in their correct positions before starting the engine.

Set the speed

Before starting the Husqvarna riding lawn mower, it is important to prepare the mower for operation. First and foremost, set the speed of the engine. To do this, turn the speed control knob to the “Choke” position and wait for a few seconds for gasoline mix with air before turning knob again to “Fast”. This will help you start your lawnmower quickly but be sure not to over-revving it by ticking off the speed control button too soon or you may cause engine damage.

Once you have set the desired speed of operation, you can proceed with starting your lawnmower. Make sure that all safety switches are in place and all ground fault interrupters are functioning properly. Ensure that the blade is clear of any debris and start by pressing primer bulb 4-5 times until it feels firm and look out for fuel appearing in transparent sight window on fuel tank during priming process. Once complete, hold ignition key in “START” position for 5-10 seconds until engine starts or bumps lightly (bumping effect differs from one engine model to another). Finally, release key from “START” position when engine successfully starts running or ticks away steadily and allow engine to warm up at slow idle speed of 1k RPM (or lower as stated on machine’s technical sheet) while checking chocking system every so often throughout entire warming period.

Adjust the cutting height

Before operating your Husqvarna riding mower, you will need to adjust the cutting height. The process for adjusting the cutting height varies slightly, depending on whether you have a manual lift or an electric lift.

  • Manual Lift: To adjust the cutting height on a manual lift mower, press the red button located near the left rear tire and move the lever up or down to change the cutting height. Be sure that both rear wheels are firmly placed into one of the pre-set slots on both sides of the lever.
  • Electric Lift: If you have an electric lift mower, start by pressing the switch located near your seat in order to activate it. Once it is activated, raise or lower your deck until it reaches your desired height and press “Set” to confirm. Each of these pre-set heights is based on a quarter inch increment from 1/4 inch (lowest setting) up to 4 inches (highest setting).

It is also important to remember to disconnect any power sources prior to adjusting any settings on your riding mower for safety purposes.

Start mowing

Once you’ve assembled your Husqvarna Riding Lawn Mower, it’s time to start mowing. Before beginning, always check the area clear of objects that could get snatched up in the blades or that could impede the path of your mower. This includes sticks, stones, toys and even animals.

Next, engage the parking brake by pressing down on the lever located between your legs while sitting in the seat.

To start mowing with your Husqvarna Riding Lawn Mower, follow these steps:

  1. Remove ignition key and check to make sure all switches are in the “off” position.
  2. Connect spark plug wire to spark plug.
  3. Open fuel valve (if applicable). If a fuel valve is not used on this model of mower, it’s important that a can of stabilizer be added to provide added protection for prolonged storage periods.
  4. Sit on seat and insert safety switch key into slot located on left side of dashboard above steering column (if applicable). Push key into slot until it clicks into place. Push clutch/brake pedal all the way down and hold it down firmly as you turn ignition key clockwise until engine starts (key should not be turned more than one full turn).
  5. Once engine starts, set choke control knob if needed before letting go of clutch/brake pedal with foot still firmly pressed against it (issues starting may occur if this step is skipped). Then turn choke control knob so indicator points towards “run.” Once you release foot pressure from brake/clutch pedal, transmission will be set in neutral position; release parking brake lever with hand pull only at this point when ready to drive lawn tractor after tractor warms up.
  6. Engine should now run smooth without coughing or sputtering; if so move foot back onto brake/clutch pedal allowing engine to continue running at idle speed.


Regular maintenance is essential for proper functioning and longevity of your Husqvarna riding lawn mower. After each use, it is important to check the oil and spark plugs, clean the air filter, and inspect the deck for any damage. Doing these simple steps will help keep your riding lawn mower in top condition and running efficiently. Additionally, performing periodically scheduled maintenance tasks will help extend the life of your riding lawn mower.

Let’s get started:

Change the oil regularly

Change the oil regularly in your Husqvarna Riding Lawn Mower to keep it running efficiently and extend its life. It’s a simple yet vital component of lawn mower maintenance that should be done on a regular basis. Here’s how to get started:

  1. Move your mower to a flat, level surface and position the chute away from the area you wish to work in.
  2. Allow the engine of your Husqvarna Riding Lawn Mower to cool before performing any maintenance work – at least an hour after mowing your lawn or completing any task involving operation of the machine should suffice.
  3. Place a large container beneath the engine area, as this is where oil will be drained out of; use a marked container such as a coffee can or bucket and make sure you have plenty of extra oil available before beginning this project.
  4. Locate and remove the drain plug from near the base of the engine – this is usually near where gasoline enters – and insert an appropriate hose over it so that oil may drain into your designated container for disposal later at an appropriate facility, such as an automotive parts store or recycling center.
  5. When finished draining, reinstall plug into its original location for secure fastening; then add fresh oil through designated tube until you reach maximum line indicated on dipstick found nearby (Note: verify type/grade of motor oil recommended by manufacturer’s manual before any purchase).
  6. Start engine once again and check for proper functioning as specified; when finished, reconnect dipstick into place so that no further leaks may occur during future use or storage periods before next scheduled procedure takes place – usually between 25-50 hours time depending on model/usage rate outlined in official operator’s manual accompanying product upon purchase date!

Sharpen the blades

Sharp blades are essential for achieving an even cut with your Husqvarna riding lawn mower. Depending on the wear and tear caused by your specific grass, you should sharpen the blades on a regular basis. You can do this by removing the mower deck and disconnecting the blades from the deck, or with a blade sharpening tool.

When sharpening the blades, be sure to use a file or grinding disc that is made of hardened steel and is specifically intended for lawnmower blade sharpening. Before you start, be sure to double-check your owner’s manual to find any specific instructions associated with your model of Husqvarna riding lawn mower.

Once you have removed the blade from the deck, lay it flat and begin sharpening along one side using smooth strokes. Make sure to keep the grinding disc at a 90-degree angle relative to the blade edge throughout the entire process and grind both sides of each blade equally. Once finished, you can reattach them to their original location on your Husqvarna riding lawn mower’s deck – then carefully tighten all bolts in place before starting up again!

Clean the air filter

Cleaning your Husqvarna riding lawn mower’s air filter is essential to maintaining the proper functioning and life of your mower engine. A clean air filter will also help ensure your mower’s fuel system continues to run as efficiently as possible. You should check your air filter periodically and replace it if needed, or when the mower is due for its scheduled maintenance.

To clean the air filter on a Husqvarna riding lawn mower:

  1. Park your mower on a level surface and shut off the engine.
  2. Disconnect the spark plug wire from the spark plug.
  3. Use a 5/8 inch wrench to carefully remove the air filter cover located above the carburetor.
  4. Pull out the outer element carefully, using a damp cloth, rub away any dirt particles that have collected on it.
  5. If there is gummy material around where the outer element borders fit into its counterpart, you may need to use some soapy water and scrub gently with an old toothbrush before rinsing off completely with water.
  6. Rinse off any excess dirt particles, ensuring all dirt has been washed away and that no foreign objects have gotten stuck on it while cleaning or reinstalling it back in place.
  7. Reinstall the cover back into place, securing tightly with 5/8 inch wrench until properly fastened in place.
  8. Reconnect spark plug wire back onto spark plug and you are now ready to start up again!

Check the fuel filter

The fuel filter is an important component of the Husqvarna riding lawn mower. It ensures that no contaminants enter the fuel system, allowing it to operate efficiently and effectively. Replacing the filter regularly helps optimize performance and maximize engine life.

Prior to starting the husqvarna riding lawn mower, it’s important to check the fuel filter for signs of wear, build-up or damage. If any of these are present, replace it with a new one as soon as possible. To do this:

  1. Turn off the ignition switch and remove any accumulated debris from around the filter housing.
  2. Loosen and remove the clamps securing the fuel lines to either side of the filter bowl or housing.
  3. Disconnect both lines from each end and use a small screwdriver or other tool to carefully pry open the lid on top (depending on model).
  4. Pull out and inspect the old filter, noting any visible signs of corrosion and other damage that may have occurred over time due to regular wear-and-tear or improper maintenance.

Stopping the Mower

When it comes to riding lawn mowers, the Husqvarna is one of the most popular brands on the market. Operating a Husqvarna riding lawn mower safely is important, and one of the most important steps of that process is stopping the machine correctly. In this article, we will discuss the steps for correctly stopping the Husqvarna riding lawn mower:

  1. Turn off the ignition switch.
  2. Disengage the blades.
  3. Wait for the blades to come to a complete stop.
  4. Lower the mower deck.
  5. Turn off the fuel valve.
  6. Engage the parking brake.

Stop the engine

When you are done mowing, it’s important to properly shut down your Husqvarna riding lawn mower so you get the most out of the machine. Follow these steps to correctly stop the engine:

  1. Put the shift lever in neutral and then press down on the parking brake release pedal with your foot.
  2. Turn off the key switch in either direction and wait at least 10 minutes before allowing anyone else to start the lawn mower. This allows time for any parts to cool down and prevents oil or fuel from potentially leaking out during an unplanned start-up.
  3. Push in on the fuel shut-off knob, located by your right leg near the commander’s seat, and turn it clockwise until it stops, then hold it in position for five seconds before releasing. This not only shuts off fuel delivery but also removes pressure from any open lines containing gasoline or oil inside the engine compartment.
  4. Disengage blades by pressing down on clutch/brake pedal with your foot and turning PTO switch off; let blades spin for a few seconds until completely stopped after being disengaged.
  5. Check that blade control is secure by making sure that no one can inadvertently start operation; also secure chipper safety door if applicable.
  6. Turn off lights if applicable, then remove key from ignition switch before leaving riding lawn mower unattended.

Put the mower in neutral

Before you can start the mower, it is important to make sure it is in neutral. All Husqvarna riding mowers come equipped with a park brake switch located on the dashboard. This switch should be in the forward position before you attempt to start the engine. Additionally, the gear shift lever must also be in its center neutral position, which will allow you to access both high and low range gears when needed. Failing to properly set these two features may prevent your mower from starting correctly.

Remove the key from the ignition

Once you have finished mowing your lawn, it is important to turn off the mower and remove the key from the ignition. You should always stop the blades from spinning before you turn the engine off by disengaging the blade or placing the speed control lever into neutral. The speed control lever will be located near your left foot or next to your seat. Once you have disengaged the blades and are certain they are not turning, only then can you shut off your Husqvarna riding mower by turning off the ignition key.

If you’ve removed the key from your Husqvarna riding mower and need to restart it, all you need to do is:

  • insert a new battery into the toggle switch located at or near your right foot when seated in a right-hand drive model.
  • slide it up into run mode, which will start your mower’s engine again.

Be sure to remember that while operating a Husqvarna riding mower, safety glasses should always be worn and children should not operate any type of powered lawn equipment—riding or push—without adult supervision.

Jacky Chou

Share post on

ToolPiP is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

Phone: 616-528-6978
323 Howard Street
Grand Rapids, MI 49505
How to start craftsman lawn mower? Lawn Mowers

How to start craftsman lawn mower?

Preparation Before you start your craftsman lawn mower, you should make sure you are...

By Jacky Chou
How to make a lawn mower faster? Lawn Mowers

How to make a lawn mower faster?

Clean and Maintain the Lawn Mower One of the simplest ways to make your...

By Jacky Chou
How to balance lawn mower blades Lawn Mowers

How to balance lawn mower blades

Preparation Proper preparation is the key to keep your lawn mower blades balanced. Before...

By Jacky Chou
How to start a troy bilt lawn mower? Lawn Mowers

How to start a troy bilt lawn mower?

Preparation Starting a lawn mower correctly is an important part of lawn care and...

By Jacky Chou
How to sharpen lawn mower blades with a grinder Lawn Mowers

How to sharpen lawn mower blades with a grinder

Safety Precautions Before attempting to sharpen the blades of your lawn mower with a...

By Jacky Chou
How much oil does a lawn mower take Lawn Mowers

How much oil does a lawn mower take

Introduction Providing the engine with enough oil is essential to keeping a lawnmower running...

By Jacky Chou
Why Are Lawn Mowers So Loud? Can They Make Less Noise? Lawn Mowers

Why Are Lawn Mowers So Loud? Can They Make Less Noise?

Loud noises are annoying, so if you are wondering why are lawn mowers so...

By Jacky Chou
Where are Toro Lawn Mowers Made? All You Need to Know Lawn Mowers

Where are Toro Lawn Mowers Made? All You Need to Know

The best lawn mowers are essential tools for people with lawns and gardens to manicure....

By Jacky Chou

Latest Posts

Why don’t schools have metal detectors? Metal Detectors

Why don’t schools have metal detectors?

History of Metal Detectors in Schools Metal detectors in schools were first proposed in...

By Jacky Chou
Why do I set off metal detectors? Metal Detectors

Why do I set off metal detectors?

What Triggers Metal Detectors Setting off metal detectors is a common occurence, particularly when...

By Jacky Chou
How to start craftsman lawn mower? Lawn Mowers

How to start craftsman lawn mower?

Preparation Before you start your craftsman lawn mower, you should make sure you are...

By Jacky Chou
How to make a lawn mower faster? Lawn Mowers

How to make a lawn mower faster?

Clean and Maintain the Lawn Mower One of the simplest ways to make your...

By Jacky Chou
How to start a husqvarna riding lawn mower? Lawn Mowers

How to start a husqvarna riding lawn mower?

Pre-Start Checklist Before you start your husqvarna riding lawn mower, it's important to do...

By Jacky Chou
How to balance lawn mower blades Lawn Mowers

How to balance lawn mower blades

Preparation Proper preparation is the key to keep your lawn mower blades balanced. Before...

By Jacky Chou
How to start a troy bilt lawn mower? Lawn Mowers

How to start a troy bilt lawn mower?

Preparation Starting a lawn mower correctly is an important part of lawn care and...

By Jacky Chou
How to sharpen lawn mower blades with a grinder Lawn Mowers

How to sharpen lawn mower blades with a grinder

Safety Precautions Before attempting to sharpen the blades of your lawn mower with a...

By Jacky Chou